Installation and Operating Manual Network 1-Channel Video/Audio Server,

MJPEG, H.264, Ethernet GLS-2301H

Ne aA

eneo

Contents

1. Safety Instructions / Maintenance...............ccccccssssssscsscessesseecseesseesrssersseesseesseesseeseestesereserssetsseesseessnessneseneas 3 2 POT AMES ENG sca 4 2 Poet vaere 4

2 ENN. 4

3. Description of the Front/Rear View.........rerarernrernrernrervrenvrrsvvrsvrrsvennvernrernrernvernrssnrssvessvessvessvessvennvennvernnssnrssvessvessven 5 FeAl EON EAU lictestusisssitatstannachtaeha altho ce 5 NNN 6

3:9 ALARM IO PIN GONE QUEALION isss-cstacsesecssvstasttatancntavstlavtatsasild dll ella lll ld dll dlls 7

34 Ne USB FUNCION erreren ANANA 8

5 ENTEN a uae 9

Ds DENN E E EA 10 Bots ENST ssc:tsieslssen seis nesnerreunrnere perenne eee Ree ERena nnn EEEE EEE R 10

4.2 Video Server SD Card Troubleshooting .........ccccscssssssssssscsscssscsssecsssesssessnessusaseresssseeuseensersseessuevsnessnesense 11

5. NETWORK COMMUN AMON esas cecccceccss cc accnetscce sn cesccestaenn cnet eu nnau nea neaan near ceac cence aaneeenaancaancaancen ater ceca bane una anees ncaa ccean onan, 12 5.1 Cable COMMECTtIONS...............cecccesccsseessscrecseessesseecseeceeecseecseeeatseausaneeaeseueseeeceeeeaesneseaeseatsaesaeseeeseseeeeeatees 12 5.1.1 Connect to a COMPUTE ............. ccc ccs eeseeesescsesssesseesseeeseecseecsesestecanecaesaesseeseeeseeeeeetentees 12

5.1.2 Connect to a LAN Switch (INTRANET)...................ccccccccscsssecsecseecssscsescsescsesseeseeseesseeeseeentens 13

5.1.3 Gonnect to a PoE Switch ...........rsororrrrnrernronnrennrennrrnnrrnvrrsvrrnvennvennrennrennrennnsnnnsrnnssnnssvensrensvennrennr 13

5.2 Configure your Video Server Network SettingS ............cc:ccccccsscssssssssesseesseecseecsesessseseseetseeeseeeseeeseeeetentens 14

Set ENDE DACP FUNCION sessilis elle allele lela lalallala 14

522 SetIPAddeSS. seede 14

5.3 TCP/IP Communication SokWare Lu uvnsnsnnmnaananandnaanaannnnenn 15

DA- TOR PSN ae neanreanenarnananan ia nntaenaa ian Raa aaa RR ARG aA 16

5.0 TGPIP Gonngurallon Seng Lunestad ttas tad ata 17

DOr SGOMNEGUON) TOSCO crcttccrtcteaxttancnccmetetuenserueeuns ann ann een eee ee 18

6. Operating Instructions for Image Software and Network ............ccccsccssesssssesssesssecseecsescsescstecseseaeeeeseeesseeeeesentess 20 61 *TVIICHO SOM ANNOUNCE NOON oiiaii E AE A dt 21 OLE- “Connecting tHe Video SENG mas nanan aaa 21

Bele2: Ghange Mage SEI 45454244 E ETENEE Ei 23

61.3: Glade the NetWork Setii esus AAA 25

6-44 Ghange the System Setting. saunamdanvamansmamianininnonininumndmneinindiniididdedd added 34

GAS Change EN NN lUaasnansneaanaaanncanagananeaianaanacanncannaannaeanaaanaaeaiacainaaianeanaaaanaeaaaanianniasaa: 42

6.1.6 View the SD Card filrS.........resarannvrnnvronvrsnersvennrennrenarennrrsnersnessnessvessrennresarenarssnvssnessnessnessreesrensrenr 49

6.1.7 Control the Speed Dome........rernrrnnvrnvvnnvrrsvennvennvennrennrennrrsvrssvessvessvennvennvennvennvssvnssvessvessvessvennvenns 50

oe PENN NN 51 EFN EEEE REES COCO TETNE T AETC O CENEEEEEEEE EOE STOETEN 52 Os SONEN 55 9: -FRUDCIOMORCGIENEP G isasun Eai AEAEE 57 APPENDIX 1 Register aS a: DDNS MGMDE?D ceitscssscrincrieverscoerentnastensnnnnvensgneranenaanensonnenvensguarabenadoeneansavensgunraensgaenibens 58 APPENDIX 2 PoE Installation Method ..............c.cccccccsscsssscsecssecessesseecseeesseeseeeesseeseseesseeseeeeseaesesuessaeessatsessessatseseeeaees 62 APPEND INS FAO nE E E EE 65

1. Safety Instructions / Maintenance

e Read these safety instructions and the operation manual first before you install and commission the unit. e Keep the manual in a safe place for later reference.

e The system may only be commissioned and maintained by personnel authorized to do this and it must only be carried out in accordance with relevant standards and guidelines.

e Never cover the ventilation slots to avoid overheating. e Never insert metal objects or any other items into the vents. This may permanently damage the unit.

e Protect your unit from contamination with water and humidity to prevent it from permanent damage. Never switch the unit on when it gets wet. Have it checked at an authorized service center in this case.

e Never operate the units outside of the specifications as this may prevent their functioning.

e Do not operate the unit beyond their specified temperature, humidity or power ratings. Operate the unit only ata temperature range of 0°C to +50°C and at a humidity of max. 80%.

e The unit should be protected against excessive heat, dust, damp and vibration. e Do not place any heavy objects on the unit. e To disconnect the power cord of the unit, pull it out by the plug. Never pull the cord itself.

e Pay attention when laying the connection cable and observe that the cable is not subject to heavy loads, kinks, or damage and no moisture can get in.

e Contact your local dealer in case of malfunction. e The connection cable should only be changed by Videor E. Hartig GmbH. e The warranty becomes void if repairs are undertaken by unauthorized persons. Do not open the housing. e Installation, maintenance and repair have to be carried out only by authorized service centers. Before opening the cover disconnect the unit from mains input. e Only use original parts and original accessories from Videor E. Hartig GmbH.

e Do not use strong or abrasive detergents when cleaning the dome. Use a dry cloth to clean the dome surface. In case the dirt is hard to remove, use a mild detergent and wipe gently.

NOTE: This is a class A digital device. This digital device can cause harmful interference in a residential area; in this case the user may be required to take appropriate corrective action at his/her own expense.

Montage- und Betriebsanleitung Installation and Operating Instructions Mode d’emploi

Instrucciones de manejo

=> www.videor.com

2. Product Features

2.1 Product Introduction

This video server is an ideal user-friendly device which brings digital benefits to your analog surveillance cameras. The tiny and compact body design can be easily installed in all kinds of analog cameras for network surveillance.

The video server adapts Texas Instrument’s (Tl’s) newest digital media processor - the Da Vinci DM 355 for efficient image operation, while also offering simultaneous dual-codec (H.264 / MJPEG) video compressions with the highest resolution, Full D1, at 30/25 frames per second in the NTSC/PAL systems, respectively. In addition, users based on different bandwidths can choose multi-profile MJPEG video streaming at different resolutions.

The video server provides stable, reliable and convenient network surveillance. It safely downloads automatic video Codec and other components, and lets you set up the control settings very easily. It provides UPnP features as well. Its USB interface is for basic network setting and updating. The SD card slot supports alarm and event recording and updating. Furthermore, this encoder board comes with the Power over Ethernet (PoE) function, and its RS-485 interface can be connected with all kinds of Pelco-D PTZ cameras.

We have launched this dual-codec video server for the more advanced digital surveillance solutions demanded by our clients. We believe this unit is the right answer to your Network surveillance problems. You will find it practical, precise and indispensable.

2.2 General Description

e 1-channel Video/Audio Server for LAN/WAN/Internet e Simultaneous Video Streaming (H.264 & MJPEG)

e Image Frame Rate: up to 25 ips. (720x576 Px.)

e RS-485 Telemetry Control Interface

e Alarm Input/Outputs

e Motion Detection

e Integrated Web Server: 10Base-T/100Base-TX

e Viewer for Monitoring, Recording and Configuration e Pre and Post Event Recording (in Client PC)

e SD Socket for Local Video Storage by SD Cards

e E-Mail Notification in Case of an Alarm

e Basic Setting via USB Interface and Network

e Power Input via Power over Ethernet and 12VDC/24VAC

FACTORY DEFAULT œ IP Address: 192.168.1.168

e Password: 9999

3. Description of the Front/Rear View

3.1 Front Panel

NETWORK

Aa 1000M

1. Act indicator Indicates the network status of the unit. The green light indicates the network is activating.

2. 10/100M indicator The green light indicates the network data are transmitting.

3. Reset button Recover to factory default.

4. SD CARD Slot This is used for system software updating and archiving / accessing critical images

5. Status indicator If this LED light is on, it means the SD card is recording or the device is updating.

6. 5pin MINI B Port The user can use a USB device cable to connect the Video Server to the USB port on the PC.

3.2 Rear Panel

AC 24V DC 42V

1. DC jack

The inlet connects to an external power supply. Connect with the 12 VDC/24VAC TUV-approved Power Supply; or connect with the UL Listed Class 2 Power Supply or ITE power supply marked 'LPS' or its equivalent.

2. Video in connector

The BNC connector is used to connect to the video output from the camera. 1 camera can be connected to the connector.

Video out connector This BNC connector provides a video signal to the main monitor.

3. ETHERNET (PoE) Connector

This is a standard RJ-45 connector for 10/100 Mbps Ethernet networks. PoE (Power over Ethernet) function: Provides power to the device via the same cable as used for the network connection.

NOTE: Please refer to the APPENDIX PoE Installation Method for more details.

4. ALARM I/0

This is an 24-PIN connector including the alarm input x 6, alarm-out x6, GND x 6, RS-485+-(2 pins), audio input and audio output items for connecting with external devices.

3.3 ALARM 1/0 PIN Configuration

eo fe YS

10.

11.

12. 13. 14. 15. 16.

17.

18.

19.

20.

21.

22. 23. 24.

RS-485 pin: D+

RS-485 pin: D-

GND1: Ground Contact

ALARM RESET (INPUT): This pin connects to an alarm-clear device for clearing an alarm (TL DV Acive) ). GND2: Ground Contact

ALARM IN 1 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL hactive) ).

ALARM IN 2 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL active) ).

ALARM IN 3 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL Sveti) ).

ALARM IN 4 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL Sveti) ).

ALARM IN 5 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL Shaetive) ).

ALARM IN 6 (INPUT): This is an alarm input which can be programmed in the menu system to Normally Open or Normally Closed (TL hactve) ).

GND3: Ground Contact

AUDIO IN Connector: The connector is used to connect the audio output from a camera or other devices. AUDIO OUT Connector: The connector provides the unit’s audio signal to a speaker or stereo.

GND4: Ground Contact

ALARM OUT 1 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL active) ).

ALARM OUT 2 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL Shaciwe ).

ALARM OUT 3 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL II Sete) ).

ALARM OUT 4 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL active) ).

ALARM OUT 5 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL Sete ).

ALARM OUT 6 (OUTPUT): This is an alarm-output trigger. Connect this to external devices such as buzzers or lights (TL active) +

GND5: Ground Contact

DC-OUT: DC-12V 350mA max.

GND6: Ground Contact

3.4 The USB Function

By connecting the video server board with a PC via the USB connector, the video server board can provide different functions.

1. Insert an SD card: As a card reader

Insert an SD card into the Video Server, then connect to the PC. You might transfer files between the SD card and the PC. Once you’ve connected your Video Server to your computer, the Windows system will detect the connection and ask you what you want to do with your SD card.

In another words, if the user connects the Video Server with an SD card and the PC via the USB connector, the Video Server can be used as a normal card reader.

2. As a configuring tool:

By connecting the Video Server with a PC via the USB connector, you can set the Network and PPPoE functions of the Video Server directly by your PC.

USD Configuration v1.02 HER DHCP a x DHCP IP Address IP Address i Network Netmask Netmas i Setting Gateway i Gateway DNS Server DNS Server PPPoE Enable PPPoE Enable PPPoE Account Account Setti n g

Password Password Mode setong g Mode seting C5S5ID CSS5ID Channel Channel

WEP Key ( WEP Key

Default Key ( Default Key

Keyl Keyl Key2 Key2 Key3 Key3

Keyt Key

LaunchiL) Apply(A) Exit{E} LaunchiL) Apply(A) Exit(E}

DHCP ON DHCP OFF

NOTE: You can click the ”Launch” button to link to the home page of the Video Server.

WARNING: After changing the settings, please click the ,,Apply” button. All of the options will be effective after removing the USB connector.

3.5 PoE (Power over Ethernet)

These technologies will enable the development of new networked appliances, by providing power as well as data over existing Ethernet cables.

The Summary Comparison of PoE Standards (Table 1) is listed as follows.

Table 1. Summary Comparison of PoE Standards

SOURCE LOAD Ethernet RJ-45 connector pin number *

STANDARD | Source DC Load REMARKS Voltage 1 2 3 5 7 1000 Connec- Voltage ior

IEEE ae om a using data | protected | DC+ | DC+ | DC- DG- for embedded PoE pairs IEEE OE RX | RX | TX | DC+|DC+| TX | DG- | DC- | (embedded) | Pdustry Standard using spare | Protected for embedded PoE pairs

The compatible PoE Hubs (Table 2), which can be used with the unit, are shown in the tables below.

Table 2. Compatible PoE Switch

FSP-804P 4 Port PoE Switch PLANET | POE-151 1 Port PoE Switch DWL-P200 1 Port PoE Switch

Connect to a PoE Switch The Standard RJ-45 PIN configuration for connecting with a PoE Switch is shown below.

Video Server to PC

to Network

Power Inlet (Using the supplied

POWLR+DATA OUT LANIN LANIN LANIN LAN IN

O 48V power supply,connect to a oe å

wall power outlet.)

PoE Switch

4. Installation

Please follow the instructions below to set up the system.

4.1 Updating System Software

If the system software of the Video Server needs to be upgraded, please take the following steps to safely process it.

IMPORTANT: Before carrying out the following procedures, please ensure the SD card is working and the file

of the system firmware is intact

1. Format an SD card using the FAT format if it is unformatted.

2. Create a directory named ,,VSERVER” in the SD card if it does not exist.

3. Copy the file of UPDATE.BIN to the VSERVER-directory.

4. If the Video Server is running, please power it off first.

5. Insert the SD CARD into the Video Server.

6. Remove the Ethernet cable from the RJ-45 port and then power on the Video Server.

7. In5to 10 seconds, a message reading ,UPDATE PROCESSING” will show up on the screen on a blue back- ground; if not, please check out steps 1 to 6 carefully or else inform your technical support while ignoring the following steps.

8. DO NOT power off the Video Server while this update process is running until the message „UPDATE OK RESET PLEASE” appears on the screen; it might take 15 to 30 seconds to appear.

9. Ifthe message „UPDATE NG RESET PLEASE” appears rather than „UPDATE OK RESET PLEASE”, please write down the error messages shown on the screen and inform your technical support, while ignoring the following steps.

10. Power off the Video Server when this update process is finished, then remove the SD card from the Video Server.

11. Reconnect the Ethernet cable to the RJ-45 port if necessary.

12. Power ON the Video Server and it will work normally if the entire update procedure goes correctly.

13. Verify the version of the system software.

WARNING:

1. Don't use the NTFS format in step 1.

2. Steps 1 to 3 have to be done on a PC.

3. Make sure the file of UPDATE.BIN is a correct one in step 3, or the VIDEO SERVER will not work normally after being updated.

4. If the power of the VIDEO SERVER is suddenly lost in step 8, please remove the SD card first and turn on the VIDEO SERVER next to test its operation. If the VIDEO SERVER remains working normally, please go back to step 4; otherwise, please inform your technical support.

5. In step 10, if the SD card is not removed and the Video Server does not get online as well, the updating process must be repeated again after rebooting the Video Server.

6. Make sure that the SD card is inserted in a correct position in step 5, or the Video Server will suffer

permanent physical damage. If the message ,,CSUM ERROR” appears in step 8, it implies a problem in the file of UPDATE.BIN.

Don’t interrupt the process while the unit is updating itself; proceed with an SD card not including any system software of the unit, or else the unit will crash.

4.2 Video Server SD Card Troubleshooting

Check if the SD card position is correct or not. Please refer to the manual for the related information.

2. After powering the Video Server on, correctly insert the SD card, and a little icon of ,SD” will show up in the upper-right corner of the monitor screen. If not, it means the device detection has failed. Please contact your technical support and ignore the following steps.

3. If no cross sign appears beside the ,SD” icon, please go on to the next step. If a cross sign appears, please check the following:

a. Is itreally an SD ,Memory” Card ?

b. Is this SD card formatted in the FAT16 format ?

c. Connect the SD card with a PC and test to see whether the PC can read the data or not.

d. Does this SD card still have the capacity for storing data ?

e. Is the SD card set to write ?

If all the answers are ,,yes” but the cross sign still persists, please contact your technical support and ignore the following steps.

4. Please make sure the function of „SD CARD ENABLE” is activated in the ALARM and SCHEDULE pages if no cross sign appears beside the ,SD” icon on the screen.

5. After recording, read the data on the web page of ,sdget.htm”. If the data cannot be read through the network, please read it instead in a PC, check the data stored in the ,VSERVER” directory and contact your technical support regardless of whether there is data or not.

WARNING:

1. Performing this troubleshooting process may need a monitor, a PC, a card reader and some cables.

2. If the SD card is removed while storing or accessing data, the data will be lost.

3. If there is a cross sign beside the ,,SD” icon, it means the SD card has been inserted into the Video

Server but cannot perform its writing function. Possible reasons are:

a. Itis notan SD memory card.

b. The SD card is unformatted or formatted in a non-FAT16 or non-FAT12 format. c. The file system is damaged.

d. The capacity of the SD card is full.

e. The SD card is set to be read only.

4. Turn off the power before inserting the SD card. Otherwise the unit may shut down.

5. Network Configuration

5.1 Cable Connections

Please follow the instructions below to connect your Video Server to a computer or a network and to choose a proper RJ-45 cable configuration for connections.

Physical specification of RJ-45 cable for Ethernet

Cat. 5 or above RJ-45

Straight through or Cross Over Straight through or Cross Over

5.1.1 Connect to a Computer

Use a cable to connect directly to a computer.

Normal or crossover cable

OOO E

to PC LAN card RJ-45

NOTE: When connecting the PC and the Video Server Board, the PC and the Video must be assigned IPs, which must be in the same class type as your network address.

5.1.2 Connect to a LAN Switch (INTRANET)

The RJ-45 PIN configuration for connecting with a LAN Hub.

to PC Network card

to Network

RJ-45

Switch

5.1.3 Connect to a PoE Switch

The Standard RJ-45 PIN configuration for connecting with a PoE Switch is shown below.

Video Server

PoE to Network RJ-45 RJ-45 | | | Power Inlet (Using the POWER+DATA OUT LANIN LANIN LANIN LAN IN WAN supplied 48V power Lu ul W Gun) PM] a © supply, connect to a wall PoE Switch | 2 3 4 power outlet.)

13

5.2 Configure your Video Server Network Settings

Upon connecting with the network hardware, you need to activate the network function and configure the proper network settings of the Video Server.

5.2.1 Enable DHCP Function

The user can use the USB function (refer to section 3.4) or the Internet Explorer (refer to section 6.1.3) to enable the DHCP function.

Network

a [7] Enable DHCP FTP SNIP Netmask 255 . 255 . 252. 0

DDNS PPPoE UPnP IP Filter

Default Gateway 19? . 168 1 .254 Primary Nameserver 19? 168 1 11 HTTP Port an

Treat lin na eae | Submit |

image | Network [System | Applicaton | SD Card | Pant |

vserver.

This function can only work if the LAN, which the unit is connected to, has a DHCP server. If the DHCP server is working, the Video Server will obtain an IP address automatically from the DHCP server. In that case, please skip section 5.2.2 (Set IP address) and follow section 5.3 (TCP/IP Communication Software).

5.2.2 Set IP Address

You need to set an IP address for the unit if the LAN unit isn’t connected to a DHCP server. Otherwise, please follow the instructions given below:

Set the IP, MASK and GATEWAY. The following is a sample setting.

IP: 192.168.1.X MASK: 290.299.299.0 GATEWAY: 0.0.0.0

NOTE: When only one unit of the Video Server is connected to a computer or LAN, you can freely assign an IP address for the Video Server. For example, there is a range of Video Server IP addresses from 192.168.1.1 to 192.168.1.255. You can pick one for use from the range of the IP. It’s not necessary to set MASK and GATEWAY; leave the settings as default.

When a Video Server is connected to a WAN, you must acquire a unique, permanent IP address and correctly configure the MASK and GATEWAY settings according to your network architecture. If you have any questions regarding those settings, please contact a qualified MIS professional or your ISP.

NOTE: When connecting to a network, each connected Video Server must be assigned a unique IP, which must be in the same class type as your network address. IP addresses are written as four sets of numbers separated by periods; for example, 192.168.1.1 Therefore, if the connected network is identified as Class C, for example, the first three sets of numbers of the Video Server IP address must be the same as the network address. If the connected network is identified as Class B, the first two sets of numbers of the Video Server IP address must be the same as the network address. If you have any questions regarding these settings, please contact a qualified MIS professional or your ISP.

5.3 TCP/IP Communication Software

Follow the instructions below to install the TCP/IP communication program into your computer. Click the Start menu from your computer, and point to the Settings/Control panel.

2 windows Update fen] Programs > * } Favorites >

AN å i Documents

i Ls] Printers í N Find > Taskbar & Start Menu... Oy Folder Options... 2 Help TA Active Desktop >

Åp Windows Update...

ge Run...

09

(6)

- & Log Off Darlayang... z ap Shut Down...

Tea

Double click the Network icon to enter the windows.

£5 Control Panel -Iof x| | File Edit View Go Favorites Ei Up Undo Delete Properties

Address ||] Control Panel

GF) NY SD

Network owe Printers Regional Management Settings

$ E > L

Telephony Users WSP Client

1 object[s] selected Configures netwc j My Computer

Click the Configuration tag, and check if the TCP/IP is included among the network components list. If the TCP/IP is included, please process section 5.5. If it is not included, please follow section 5.4 to install the TCP/IP.

Network 2!

Configuration | Identification | Access Control |

The following network components are installed: E] Client for Microsoft Networks NE 2000 Compatible

X IPx/SPx-compatible Protocol

Remove | Properties |

Primary Network Logon:

[Client for Microsoft Networks v] File and Print Sharing... |

Description

TCP/IP is the protocol you use to connect to the Internet and wide-area networks.

5.4 TCP/IP Installation

Network 21x!

Configuration | Identification | Access Control |

The following network components are installed:

E] Client for Microsoft Networks NE2000 Compatible

IP/SP-compatible Protocol

X NetBEUI Select Network Component T: 3 2|x Click the type of network component you want to install: Primary Network Logon:

[Client for Microsoft Network,

File and Print Sharing...

Descriptio

Select Network Protocol

x|

Click the Network Protocol that you want to install, then click OK. If you have an installation disk for this device, click Have Disk.

Manufacturers: Network Protocols: å $ Fast Infrared Protocol [ae IP</SPX-compatible Protocol

RO eres 5 Microsoft 32-bit DLC ar

$ Microsoft DLC 5

During the installation, you will be requested to insert the Windows CD-ROM. After installation, the PC may be restarted.

16

5.5 TCP/IP Configuration Setting

Click Start -> Settings -> Control Panel -> Network Select TCP/IP, and then click Properties.

Before processing the Video Server installation in a WAN, If not, please contact your ISP provider.

Network

Configuration | Identification | Access Control |

The following network components are installed:

ΠClient for Microsoft Networks NE 2000 Compatible

y IFx/SPx-compatible Protocol X7 NetBEUI

Add...

Remove | i

Primary Network Logon:

[Client for Microsoft Networks v] File and Print Sharing... |

m Description

TCP/IP is the protocol you use to connect to the Internet and wide-area networks.

please make sure the Internet connection works properly.

TCPAP Properties

Bindngs | Advanced | NewiOS | DNS Configuration | Gateway | WINS Configuration IP Address

An IP address can be automatically assigned to this computer If your network does not automatically assign IP addresses, ask your network administrator for an address, and then type it in the space below.

C Obtain an IP address automatically —© Specity an IP address; ———

Set Mack

IP Address:

If you are using a DHCP server, please select Obtain an IP address automatically. Any assigned IP address for the connected Video Servers must be in the same class type as the server. If there is no DHCP server, please select specify an IP address and type in the IP address of your PC. This IP address must be different from other network IP

devices but in the same class type.

NOTE: The IP address of a Video Server in a network must be unique to itself as opposed to those of the

other chosen PCs, but in the same class type.

17

5.6 Connection Testing

With the previous settings, follow the instructions below to ensure whether you have established the connection successfully.

Click Start -> Programs -> MS-DOS Prompt

A Accessories > & Microsoft Access

> Microsoft Binder

DE Microsoft Excel

251 Microsoft Outlook

(= Microsoft PowerPoint

BY Microsoft Word

a RECS

EN Windows Explorer

Favorites TY Documents Eh Settings Q Eind

2 Help But.

Type in ping 192.168.1.168 then Enter. (See the sample screen below) e This IP is the Video Server IP address that is assigned for the connected Video Server in step 2.

jerasoftik? Windows 98 Foceppr iht Miærasaft Carp 1941-1999.

NWINDOSS-pihg 192, 168. 1.168

18

If you receive a response as in the sample screen below, the connection hasn't been successfully established. Please re-check all the hardware and software installation by repeating steps 1 to 5. If you still can’t establish the connection after re-checking, please contact your dealer.

NeErpsoftik) Windows J4 (Cycopyright Microsoft Carp 1981-1999.

Destination host unreachable. Destination hest unreachable.

Ping rad for 192.160.1.168-

Packets: Sent = 4, Received = 0, Lost = 4 {100% loss}, Kir net round trip times ian mitli=seconds:

Minimum = ng, Maximum = 905, Average =

2 VI NDE _

If you receive a response as in the sample screen below, you have successfully made the connection.

ror =) holm) Fa) oS ala licresoftckh) windews 98 (C}copyright Microsoft Corp 1981-1999. c:\winoonping 192.168.1.268) type LAN CAMERA IP address

Pinging 1927.165.1.155 with 32 bytes of data:

Reply from 192.168.1.168 byres=32 time<Loms TTL=12a i i Reply from 1923.168.1.168 bytes=3? time<Lons TTL=124 connection is

Realy from 192.168.1.168 bytes=32 time<lons TTL=128 Healy from 192,168.1.168 bytes=3? time<Löms TTL=123 successful

Ping Statistics Får 192,168.1. 158

Packets: Sent = 4, Received = Lott = 0 (0% Toss}, pAraximate round trip tines in Mareos:

minimum = Ons, Maximum = ms, Average = Ons

Ei AENEAS >

19

6. Operating Instructions for Image Software and Network

Two choices of software are available for linking with the Video Server: (1) the Microsoft Internet Explorer; and (2) the eneo GL-Manager, a network browser in a PC which provides the functions of monitoring remote zones or watching recorded data through the TCP/IP protocol.

The details are listed as follows.

RJ-45 PIN configuration for Ethernet

no. [pus EN 4 fromme

5 moro es [am å omea

Physical specification for Ethernet

Wire Type Gat. 5 Connector Type RJ-45

Hub Wiring Configuration Straight through or Cross Over PC Wiring Configuration Straight through or Cross Over

NOTE: If you use a laptop to connect the Video Server, please set the Power schemes to the ,,Home/office Desk” item to get the higher quality of surveillance.

1. Open the Control Panel by clicking Start -> Control Panel.

2. Open the Display Properties by clicking Display -> Display Properties. 3. Click the Screen Saver item.

4. Click the „Power” button.

5. Select „Home/office Desk” under the Power schemes item.

20

6.1 Microsoft Internet Explorer

6.1.1 Connecting the Video Server

. Start up the Microsoft Internet Explorer, and then follow the steps below to connect the Video Server. . Click the URL block at the top of the window. . Enter the URL address of the Video Server into the URL block and press the ,,Enter” button to enter the home page.

. Scroll to the bottom of the page, with its five icons, ,,Image”, ,,Network”, System”, Application”, ,SD Card” and ,»Pan/Tilt”. Whichever you click, the page headlined „Enter Network Password” will appear.

. Type in the „User Name” and „Password” in the appropriate spaces. 6. Click the „OK” button to set your entries, and automatically exit the page.

HR ow N

OT

NOTE: The default User Name” and ,Password” are admin and 9999 respectively.

NOTE: The page headlined ,,Enter Network Password” is shown below. Please enter the user name and password of the Video Server when you see it. If either the user name or the password is incorrect, please check the input data and rectify it if and as necessary.

NOTE: Once authorized succesfully, it will not appear again until you close the window and reconnect it.

NOTE: The initial sequence of proceeding is to type in your IP address and click the ,,Enter” button to access the home page. If and when you revise or change data in the ,SYSTEM USERS” page, the sequence will alter to initially show the „Enter Network Password” page.

Connect to 192.168.0.92

Cl Remember my password

[om]

21

Browsing images from the Video Server

The images from the Video Server will be displayed on the home page while going online with the Video Server. Some buttons of the home page are provided for further setting.

MEG “|101 ed w i ita

Homepage of MJPEG mode Homepage of H.264 mode

Click the Image button to enter the image-setting page.

Click the Network button to enter the network-setting page.

Click the System button to enter the system-setting page.

Click the Application button to enter the application-setting page.

Click the SD Card button to open the FILELIST of the MEMORY CARD window, if the SD card is inserted. Click the Pan/Tilt button to change the Pan/Tilt/Zoom settings.

Click the sPEG | 1:01 ~] to change the six pairs of resolution and quality which you already arranged in the „Multi Profile” setting page (MJPEG mode only).

NOTE: The maximum video capture resolution of CIF for PAL is 352x288 pixels. The maximum video capture resolution of HALF D1 is 720 x 288 pixels. The maximum video capture resolution of D1 is 720 x 576 pixels.

Click the 11102005 14:31:37 | button to change the time/date display mode.

Click the 0 button to play the live audio. Click once again to deactivate.

Digital zoom function: Click the left mouse button on the video display area, and it will show the zoom-in images. Double click the left mouse button to see the maximum size. Click the right mouse button on the video display area, and it will show the zoom-out images. Double click the right mouse button to come back to the normal size.

22

6.1.2 Change Image Setting

Please follow the steps below to change the image setting through the network if necessary.

1. Click the Image button on the home page to enter the image-setting page.

vserver

O Activex

©AJAX

|

2. Adjust the image setting including ,,Device Title” and ,,Viewer Type” if necessary. 3. Click the Submit button to submit the new image setting.

4. Click the Multi Profile button to enter the MultiProfile image-setting page. Select an ID (1-6) from the drop-down

list then set its resolution and quality. Click the Submit button. Then you can exchange the pairs of resolution and quality directly in the Home page.

kai ap [say aay MultiProfile

23

5. Click the H.264 Image button to enter the H.264 image-setting page. Adjust the image setting including »Resolution”, ,, Quality” and ,Frame Rate” if necessary.

Quality

Frame Rate:

6. Click the Fine Tune button to enter the Image Fine Tune page to set the details of the device including: ,Brightness”, ,Contrast”, ”Hue” and ,Saturation”. Click the Default button to reset the channel image settings.

NOTE: The revised image will appear immediately after any change in made.

Bagnmess: (2120 [Glovzss) Contrast: (128 [2](o-255) Hue: i Glo~255) Saturation: (ji2a ()0~255)

(Reset All Image Parameters)

7. Click the Home button to return to the home page while the new image setting acts on the images to effect the desired changes instantly. (If the setting has not been changed by the above steps, any (re)entry onto the home page will find images in their earlier or original setting.)

24

Description of function keys

Device Title: Type in the Video server title in the given space.

Resolution: MJPEG mode - Scroll to choose the image resolution from „352 * 240”, "720 * 240” or ”720 * 480” (NTSC); „352 * 288”, „720 * 288, or „720 * 576, (PAL).

H.264 mode - Scroll to choose the image resolution from „Full D1”,”Half D1” or „CIF”.

Quality: Scroll to choose the image quality out of a spectrum of qualities ranging from „highest”, ”high”, „medium”, and „low” to „lowest”.

Brightness: Enter your desired quality of image brightness from a spectrum of 0 to 255. Contrast: Enter your desired quality of image contrast from a spectrum of 0 to 255. Hue: Enter your desired quality of image hue from a spectrum of 0 to 255.

Saturation: Type in the saturation level in the blank (0 to 255).

© : Back to the last page.

© : Reload the page.

© : Go to the next page.

6.1.3 Change the Network Setting Please follow the steps below to change the network setting through the network if necessary. e Set the network options and IP address.

1. Click the Network button in the home page to enter the Network page.

Network

> F enable ore FP SNTP Nermask 255 . 255 . 252 n

DDNS PPPOE UPnP

Default Gateway 19? . 168 1 . 254 Primary Nameserver 19? . 168 1 11 IP Filter HEIP PO 80 Tralla

| Submit |

Image | Network | System | Application | SO Card | Pan/Tilt |

vserver.

at Et iia

A If you modify any IF addosss or HTTP Port of network ættuig

Fiese sevteat LE Wwowses viti arw IP addørss os HTTP Port.

2. A warning message -J will appear: If you modify any IP address or HTTP Port of network setting. Please restart the IE browser with the new IP address or HTTP Port. Click „OK” to continue.

25

3. The accessible networks here are the , FIP”, the ,SMTP”, the ,SNTP”, the ,DDNS”, the ,PPPoE” and the JIP Filter”.

4. Fill in the „IP Address”, ,Netmask”, Default gateway”, Primary nameserver”, and HTTP Port” if necessary. 5. Click the Submit button to submit the new network setting. 6. Click the Home button to return to the home page.